For Modbus systems
Analogue signal converters

XCIO4RMB

NEW

255.40 + VAT

PCS PER PACK1

In stock

In stock

Analogue signal converter IN: RTD / OUT: Modbus RTU

Modbus RTU output
Insulation: 1.5 kVac, 3-way isolation
4 input channel
parametrization via Modbus RTU
CaburLab software is available for free

Additional information

Series
Code
Type
HS code
INPUT TECNHICAL DATA
Signal type IN
Input range IN
Input impedance IN
Parametrization IN
OUTPUT TECHNICAL DATA
Signal type OUT
Status indication
GENERAL TECHNICAL DATA
Power supply voltage
Current consumption
Accuracy
Linearity error
Transmission frequency
Resolution
Baud rate
Parity
Operation temperature range
Insulation
Insulation type
EMC Standard
Overvoltage category / pollution degree
Protection degree
Connection terminal IN / OUT
Housing material
Dimensions (LxHxD)
Approximate weight
Mounting information
ACCESSORIES
Mounting rail (IEC60715/TH35-7.5)
APPROVALS AND MARKINGS

NOTES

Factoy setting: 500 Ω input

For further information see PDF catalog

Cabur
BT003
End bracket for rail type TH35, suitable for NU1051S, NU0851S,...
Cabur BT007 END BRACKETS BT SERIES
BT007
End bracket for rail type TH35, suitable for NU1051S, NU0851S,...
Cabur BT003 END BRACKETS BT SERIES
BT005
End bracket for rail type G32 and TH35, suitable for...
CABUR PR003 MOUNTING RAILS PR SERIES
PR905
Mounting rail TH35-7,5 with holes
CABUR PR003 MOUNTING RAILS PR SERIES
PR003
Mounting rail TH35-7,5
CABUR PR003 MOUNTING RAILS PR SERIES
PR005
Mounting rail TH35-7,5 with holes
CABUR PR003 MOUNTING RAILS PR SERIES
PR903
Mounting rail TH35-7,5

Modbus-RTU programmable analog converters

The XCIO4 devices are analog converters, fully programmable through a PC application and with ModBus communication inter-face.
There are different models:

  • XCIO4VMB voltage converter
  • XCIO4IMB current converter
  • XCIO4RMB thermoresistance and potentiometer converter
  • XCIO4TMB thermocouple converter
  • XCIO4RLYMB, actuation module

Each device has up to four independent channels, it is remotely configurable through the ModBus interface and in alternative with a uUSB port with no need for additional power supply.
The devices are fully programmable by means of CaburLab software application or directly accessing the ModBus registers by means of a PLC.
The XCIO4RLYMB can be configured to have a default safe condition called safestate that allows to set the state of the output when the power is off and/or when the device is remotely controlled.

Communication bridges

The XBRI series is based on two different interconnection bridge typologies.
The XBRIRS485CP is a gateway which allows the connection between RS-485 interconnected devices towards a ModBus-TCP over Ethernet network .
The XBRIRS485ET and XBRIRS485WI are bridges with the capability to connect RS-485 devices to a 10/100 Base T Ethernet network based upon TCP/IP.
The Ethernet – RS485 communication passe through a virtual communication interface. The bridges parameters can be configu-red through a dedicate telnet interface (IP address, subnet mask, etc.).

Ethernet Switches

The XSWET5UP and XSWET5UP series of Din-rail Entry-level Unmanaged Ethernet Switches for industrial applications are highly compacted 5 and 8-port Ethernet switches that support IEEE 802.3/802.3u/802.3x with 10/100M, full/half-duplex, RJ45 ports.
The XSWET5UP and XSWET5UP switches are rated to operate at temperatures ranging from -10 to 60°C. The switches can be easily installed on a DIN-rail as well as multi-directional panel mounting.

IN THE SAME CATEGORY

ISCRIVITI ALLA NEWSLETTER

Name(Required)
Email(Required)
Address(Required)
Privacy(Required)
The consent to the subscription to the Cabur Newsletter can be revoked, at any time, using the unsubscribe procedure available on the emails sent. PRIVACY POLICY

CABUR CUSTOMER CARE

for technical support
+39 019 58999.219  customercare@cabur.it
for commercial support
+39 019 58999.609 vendite@cabur.it

from monday to friday 8:30-12:30 13:00-17:00